Dell PowerConnect 6248 Firmware Upgrade

Aşağıdaki komut ile switchin mevcut firmware versiyonunu kontrol ediyoruz.
console#show switch
Management    Preconfig     Plugged-in         Switch          Code
Switch    Status      Model ID      Model ID           Status         Version
—— ———— ————- ————- ——————— ——–
1      Mgmt Switch  PCT6248       PCT6248       OK                    2.2.0.3
Mevcut configin yedeğini  olası problemlere karşı tftp sunucusuna alıyoruz.
console#copy startup-config tftp://10.255.255.19/6248conf.cfg
Mode……………………………………. TFTP
Set TFTP Server IP……………………….. 10.255.255.19
TFTP Path……………………………….. ./
TFTP Filename……………………………. 6248conf.cfg
Data Type……………………………….. Config Script
Source Filename………………………….. startup-config
Management access will be blocked for the duration of the transfer
Are you sure you want to start? (y/n) y
328 bytes transferred
File transfer operation completed successfully.
Dell’in sitesinden güncel Firmware’i indirerek tftp sunucusundan image’ı switch’e çekiyoruz.
console#copy tftp://10.255.255.19/PC6200v3.2.0.7.stk image
Mode……………………………………. TFTP
Set TFTP Server IP……………………….. 10.255.255.19
TFTP Path……………………………….. ./
TFTP Filename……………………………. PC6200v3.2.0.7.stk
Data Type……………………………….. Code
Destination Filename……………………… image
Management access will be blocked for the duration of the transfer
Are you sure you want to start? (y/n) y
TFTP code transfer starting
9709280 bytes transferred
Verifying CRC of file in Flash File System
Unpacking the image file.
TFTP download successful. All units updated code.
File transfer operation completed successfully.
İlgili komut ile flash üzerindeli erişilebilir image versiyonlarını görüyoruz
console#show version
Image Descriptions
image1 : default image
image2 :
Images currently available on Flash
——————————————————————–
unit      image1      image2     current-active        next-active
——————————————————————–
1     2.2.0.3     3.2.0.7             image1             image1
Son yüklemiş olduğumuz versiyonu aşağıdaki komut ile aktif ediyoruz ve ardından switch’i yeniden başlatıyoruz.
console#boot system image2
Activating image image2 ..
console#reload

Restart sonrasında switch Boot Menüsü karşınıza çıkacak ve Start Boot Menü diyerek menü özelliklerine giriyoruz.
Boot Menu Version: 21 November 2008
Select an option. If no selection in 10 seconds then
operational code will start.
1 – Start operational code.
2 – Start Boot Menu.
Select (1, 2):2

Update boot code seçeneğini seçerek yeni firmware için açılış kodlarının değişmesini sağlıyoruz.
Boot Menu 21 November 2008
Options available
1  – Start operational code
2  – Change baud rate
3  – Retrieve event log using XMODEM
4  – Load new operational code using XMODEM
5  – Display operational code vital product data
6  – Reserved
7  – Update boot code
8  – Delete backup image
9  – Reset the system
10 – Restore configuration to factory defaults (delete config files)
11 – Activate Backup Image
12 – Password Recovery Procedure
[Boot Menu] 7
Do you wish to update Boot Code and reset the switch? (y/n) y
Boot Menu 3.2.0.7
Select an option. If no selection in 10 seconds then
operational code will start.
1 – Start operational code.
2 – Start Boot Menu.
Select (1, 2):
Operational Code Date: Fri May 14 19:08:14 2010
Uncompressing…..
ve Sistem son versiyona güncellendi, afiyet olsun 🙂
0 Paylaşımlar

Bir cevap yazın